Engine assembling Volvo B18 and Volvo B20

Once installed, the bushings needs to be reamed to the proper size. This procedure, along with honing the large end, is best done at a proper engine shop.

Step 1

Clean the block

First step is cleaning the block and all its channels properly to remove any debris or granule left from the machining of the block.

Clean and install fitting, art.nr 418416, which lubes the timing gears.

Step 2


Install the cam shaft

Several grinds are available. From these ones we built, two were equipped with A-cam, p/n 460490, the other two with K-cams, p/n 1218581. First, apply molybdene grease to all cam lobes to protect while breaking in the cam.

The same paste will later be used on the lifters when the time to install those have come. Cam bearings could be lubed at this time as well, with engine oil or assembly grease, art.nr V903.
Which one to use is depending on how long it will take until the engine is started.

Carefully insert the cam shaft in the engine to avoid damages to the bearings. Once it’s in place, install spacer, p/n 418363, and the thrust flange. Reusing the old flange is usually OK simply by flipping it over as it only wears down on the inside. Assuming of course that this hasn’t already been done in the past.

Start by installing the bearings, thereafter apply engine oil or assembly grease to them.

Clean the cups properly before inserting the bearings. We used ACL aluminum bearings, p/n 271215-ACL.

Carefully clean the crank shaft, especially in all oil channels, and then put it in place in the engine.

Put the caps in place, and tighten them to the specified torque (12-13 Kgm).

Do this operation in three steps, making sure the crank rotates freely after each tightning.

Step 4
Mount timing gears

The engines with A-camshaft gets timing gears in fibre/steel, art.nr 270690, and the two engines with K-cam gets timing gears in aluminum/steel p/n 270690AL.

First mount the crank gear. Heat it up a little bit to make it easier to slide it on to the crank. A hotplate works fine.

While you heat up the gear you can mount the index key, p/n 910123 and the index key in the camshaft, p/n 910118. When the gear is hot enough, just slide it on to the crank with the marking facing outwards. If it wasn’t hot enough you might have to use a hammer and carefully hit it to make sure it’s all the way in. NB! Knock carefully!

Then it’s time for the cam gear. Also this gear could use some heat but not like the crank gear. Especially if you use the fibre gear. Easiest is to use a hot air gun.

Mount the cam gear so the marks line up and push it in as far as you can by hand. Then mount the nut p/n 150169 and screw in the gear.

NB! Never use a hammer to mount the cam gear.Finish the job by torque the nut to 13-15 Kgm. Use a plank and put it between the block and crank to avoid the engine from turning over while fastening the nut.

Step 5 A
Assembly piston (p/n 275194 for the B18 and p/n 272004 for the B20)/rod and also assembly rod bearings and piston rings.

Start with removing the cap from the rod. While these have been machined the cap bolts are torqued and it’s important to fasten them in a proper way while loosening the nuts. This to avoid bending the rod.

Mount the bearings in their position.

NB! Wipe clean before positioning the bearing. Here we used ACL art.nr 271052-ACL.

Then it’s time to put oil or assembly lube on the rod bearings, the bushing in the small end of the rod and in the pin hole in the piston.

After that it is time to mount the piston and the rod together.

Here you have to make sure you do it right. The arrow or mark on the piston should point forward and the number on the side off the big end of the rod should end up at the opposite side of the engine as the cam shaft. Push in the piston pin (an easy push with the thumb should be enough) and then mount the locks.

Now it’s time for piston rings! Here it’s important to read the instructions to make sure you mount them with the right side up. Usually there is some kind of marking like a dot or some text that tells wich side should go up.

For the engine with the A-cam (2 B20) we used cast iron rings art.nr 275336 and the engines with the K-cam got other rings, art.nr 275283 for the B18 and 275336MOLY for the B20.

Some rings you can mount either way.
So read the instructions carefully and find out how to do it.

The best is to use piston ring pliers to make the assembly easier and to avoid breaking a piston ring. This tool has art.nr 4234.

Step 5 B
Assembly of piston and rod in engine.

Here you need a tapered ring compressor (best solution!) or some other type of piston ring compressor.

We used a homemade version made of a 0.8 mm metal sheet and welding pliers.

Use plenty of oil on both the cylinder walls and inside the piston ring compressor.

Positioning
Position the crank so it’s as far down as possible in the cylinder you are going to mount.

At the same time as you knock down the piston make sure that the big end is off the rod or the rod bolts don’t hit the crank and ruins the journals.

Step 6
Painting the engine

We used Volvo-red engine enamel, art.nr. 9434521.
You can also have it in a spray can, art.nr. 9434521-1.